View BVU-3R16BA4_4921774.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

BRIGHT VIEW ELECTRONICS CO.,LTD
ULTRA BRIGHTNESS LED LAMP
PACKAGE CONFIGURATION
BVU-3R16BA4
DESCRIPTION
Dice Material : GaN Blue Light Color : Blue Color Lens Color : Water Transparent Stand-Off P/N : BVU-3R16BA4 R
3.2 3.2 3.0 3.5 1.0 1.0Max.
3.2
RADIATION PATTERN
-30 0 30
9.80.5
1.3 25.4Min. 1.0 25.4Min.
-60
60
CATHODE 0.5 2.54
CATHODE
100 75 50 25 0 25 50 75 100 Relative Luminous Intensity ( Iv % )
1.0Min.
2.54
Tolerance 0.25
ABSOLUTE MAXIMUM RATINGS AT Ta = 25
PARAMETER Power Dissipation (PD) Continuous Forward Current (IF) Peak Forward Current ( 1/10 Duty Cycle , 0.1ms Pulse Width ) (IFP) Reverse Voltage (VR) MAX. 120 30 160 5 0.4 UNIT mW mA mA V mA/oC
Derating Linear From 25 Operating Temperature Range (Topr) 30 to 80 Storage Temperature Range (Tstg) 40 to 100 Lead Solder Temperature 1.6 mm Below Package 260 for 5 seconds (Tsld)
ELECTRICAL / OPTICAL CHARACTERISTICS AT Ta = 25
SYMBOL VF IR p d 21/2 IV PARAMETER Forward Voltage Reverse Current Peak Emission Wavelength Dominant Wavelength Viewing Angle Luminous Intensity TEST COND. I F = 20 mA V R = 5V I F = 20 mA I F = 20 mA I F = 20 mA I F = 20 mA MIN. TYP. 3.2 465 470 40 1680 MAX. 4.0 10 UNIT V A nm nm Deg mcd
1300
BIN GRADE LIMITS (IF=20 mA) LUMINOUS INTENSITY / mcd
Bin Min. Max. K 1300 1680 L 1680 2180 M 2180 2800 N 2800 3600 Tolerance 15%mcd
BIN GRADE LIMITS (IF=20 mA) DOMINANT WAVELENGTH / nm
Bin Min. Max. BM 460 465 BN 465 470 BO 470 475
*Bright View reserves the rights to alter specifications and remove availability of products at any time without notice. *Dominant Wavelength, d is according to CIE Chromaticity Diagram base on color of lamps. *1/2 is the off-axis angle where the luminous intensity is one half the on-axis intensity. *These products are sensitive to static electricity. Caution must be taken strictly to avoid static electricity.
2009/2/19 - B
BRIGHT VIEW ELECTRONICS CO.,LTD
ULTRA BRIGHTNESS LED LAMP
BVU-3R16BA4
TYPICAL ELECTRICAL / OPTICAL CHARACTERISTIC CURVES
FIG. 1 Forward Current vs. Forward Voltage ( Ta = 25 C ) FIG. 2 Relative Intensity vs. Forward Current ( Ta = 25 C )
40 35 30 25 20 15 10 5 0
3.0 2.5 Relative Intensity 2.0 1.5 1.0 0.5 0
Forward Current ( mA )
2.2
2.7 3.2 3.7 Forward Voltage Vf ( V )
4.2
0
10 20 30 Forward Current If ( mA )
40
FIG. 3 Forward Voltage vs. Temperature 1.2 Relative Intensity @ 20mA Forward Voltage @ 20mA 1.1 1.0 0.9 0.8 -50 3.0 2.5 2.0 1.5 1.0 0.5
FIG. 4 Relative Intensity vs. Temperature
-25
0
25
50
75
100 125
0 -50 -25
0
25
50
75
100 125
Ambient Temperature Ta ( C ) FIG. 5 Relative Intensity vs. Wavelength ( p ) ( Ta = 25 C ) IF-DC Forward Current ( mA )
Ambient Temperature Ta ( C ) FIG. 6 Maximum Forward Current 40 30 20 10 0 0 vs. Temperature
1.0 Forward Intensity @ 20mA
0.5
0 400
450 500 Wavelength ( nm )
550
20 40 60 80 100 Ambient Temperature Ta ( C )
120
2009/2/19 - B
BRIGHT VIEW ELECTRONICS CO.,LTD
ULTRA BRIGHTNESS LED LAMP
BVU-3R16BA4
CAUTION FOR CLASS 1 ESD ( MACHINE MODE ) Gallium Nitride (GaN) based light emitting diodes (LEDs) are extremely sensitive to electrostatic discharge (ESD). Users are strongly recommended to take necessary meter to test the static and avoid ESD when handing these products. Bright View's BA, GN, WI series products are GaN based materials and are classified as "Class 1",( ESD endurance 50V or lower ), any manufacturing site or workstation where GaN devices are handled should be rated and controlled at 50V or below. Proper grounding of products or machines ( via 1M ), using static dissipative mats, static dissipative containers, static dissipative working uniferms and shoes are considered to be effective against ESD. An ionizer is recommended in the facility or environment where ESD may be generated easily, and soldering iron with a grounded tip is also recommended. To install a protection device in the LED circuit to ensure the surge current and voltage not exceeding the max rating during on/off swithing. When inspecting the final products in which LEDs are assembled, it is recommended to check whether the assembled LEDs are damaged by ESD or not. It is simple to find damaged LEDs by light-on or a VF test at lower current (below 1mA is recommended). ESD damaged LEDs will show some unusual characteristics such as the remarkable increasing of leak current, the forward voltage become lower, or the LEDs do not light on at the low current.
2009/2/19 - B
BRIGHT VIEW ELECTRONICS CO.,LTD
ULTRA BRIGHTNESS LED LAMP
BVU-3R16BA4
Apply to LAMP(DIP) series. Description: ( 1 ) Manual soldering (Solder Iron) (1.1) Temperature at tip of the iron: 300C Max. (1.2) It's banned to load any stress on the resin during soldering. (1.3) Soldering time: 3 sec. Max.(one time only) (1.4) Leave 3mm of minimum distance from the base of epoxy. ( 2 ) Dip Soldering(Wave soldering-Solder Bath) (2.1) Leave 3mm of minimum distance from the base of the epoxy. Soldering beyond the base of the tie bar(stand off) is recommended. (2.2) When soldering, do not put stress on the LEDs during heating. (2.3) Cutting the leadframes at high temperatures may cause LED failure. (2.4) Never take next process until the component is cooled down to room temperature after reflow. (2.5) After soldering, do not warp the circuit board. (2.6) The recommended dip soldering profile is the following:
Degree C.
300.0 275.0 250.0 225.0 200.0 175.0 150.0 125.0 100.0 75.0 50.0 25.0 0.0
MAX 260 C 5 sec. >20 C
Temperature ( C )
4 C / sec. 150 C
0.0
50.0
100.0
150.0
200.0
250.0
300.0
Time ( sec. )
2009/2/19 - B
BRIGHT VIEW ELECTRONICS CO.,LTD
ULTRA BRIGHTNESS LED LAMP
BVU-3R16BA4
Label 1
Label 2
Bright View
PART NO.: LOT NO.: GRADE: Q'ty Xpcs
Electronics Co.,Ltd.
Bright View
PART NO.: LOT NO.: GRADE:
Electronics Co.,Ltd.
BVU-XXXXXXXX
QA
3mm or 5mm Polybag
Pb - Free / RoHS Compliant X: Bin grade : Wavelength : Vf
Anti-electrostatic bag
Q'ty pcs QA Pb - Free / RoHS Compliant
ELECTROSTATIC SENSITIVE DEVICES DO NOT OPEN OR HANDLE EXCEPT AT A STATIC-FREE WORKSTATION
BOX Dimension(cm): 29*25*15
25
BVU - X X X X X X X R
Stand-offs Luminous Grade-refer to the selection guide for BIN options Lens Color-refer to lens color (1) to (9) Dice Code-refer to the selection guide Lens Configuration-refer to lens drawing View Angle-refer to the selection guide (A) to (Z) Outline Dimension-refer to the outline dimension
29
3
15
TYPE Q'TY N,W G,W C.NO
PCS KGS KGS
Label 1 or Label 2 attach on it.
Device 5mm(T-1 3/4) 3mm(T-1) Blue / Green / White
Q'ty / Polybag (pcs) 1000pcs 1000pcs 500pcs
Polybag / Box A 14 bags 20 bags 18 bags
Fig. Label 1 Label 1 Label 2
32 53
RE Y
CARTON Dimension(cm): 53*32*33
33
ITEM NO. DEVICE: Q'TY N. W.: G. W.:
PCS. KGS. KGS.
4 Boxes / Carton
5mm : 56,000pcs 3mm : 80,000pcs Blue / Green / White : 36,000pcs
2009/2/19 - B

▲Up To Search▲

Price & Availability of BVU-3R16BA4

	To Download BVU-3R16BA4 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .